How to Mount Wood Fence Panels Between Posts

Answer

Purchasing fence panels that are 8 feet in height is one of the easiest methods to construct a fence. Panels are not only cost efficient but also save a significant amount of time since they eliminate the need to individually connect rails and slats to the structure. When compared to the cost of the slats and rails required to construct your own panel, the price of The Home Depot’s weather-resistant wood privacy panel, which measures 8 feet by 6 feet and is constructed from wood, is around $100.

When installing the fence posts, you will need to pay somewhat more attention to detail if you want to construct your fence out of panels. They must have a gap of precisely 8 feet between them. When you space them too far apart, it creates a gap that you can’t close. Setting them too close together is also troublesome since it prevents you from modifying the panels without a significant amount of effort, and one of the reasons you picked panels in the first place was to reduce the amount of work you had to do.

There are two strategies that might be helpful. The first thing that has to be done is to construct a jig for evenly spacing the fence posts. The second step, which involves using blocks to place the panels, should be performed after the posts have been correctly fastened and the concrete has had time to dry.

How to Set Posts When You Plan to Install a Panel Fence

When putting in fence posts, it is usual practise to begin at one corner and mark the locations of the posts along the fence line using a string that has been stretched down the fence line from corner to corner. You may be able to create markings at correct 8-foot intervals, but when you dig, you’ll probably make a mistake since it’s simple to make the hole too much to one side of the mark. Nevertheless, you could be able to make the marks.

To get back on track, cut a piece of timber measuring two by four and eight feet long to use as a spacer. Now you can install the first corner post, check to see whether it’s level, and backfill around it to keep it stable. Put a level on the spacer, then move the spacer from that post to the next hole and extend it so that it reaches the next hole. To check that the first post is still in touch with the second one after you have moved the spacer up and down the length of the first post: After that, you need to backfill and level the post in the direction that is perpendicular to it.

If you continue around the perimeter of the fence in this manner, you will ensure that every post is precisely the distance away from its neighbours that is necessary in order for you to be able to fit the panels and connect them. Hold off on throwing away the spacer for the time being. You cannot do without it.

Panels Follow a Step Pattern on Sloped Ground

It is possible to build fence panels with angled ends to follow the slope of the ground, but it is a lot of effort, and the fence panels that you purchase at the shop are not at all likely to be built in that manner. As a consequence of this, the majority of panelled fences feature a step pattern, which implies that each panel is installed in a horizontal orientation. The end of the panel that is on higher ground is elevated to a conventional distance from the ground, which is typically 4 inches, but it is raised on the lower post by an amount that is sufficient to maintain the panel level.

This indicates that the bottom post has to be elevated to a height that allows it to reach beyond the top of the panel. Because of this, fence builders often do not trim the tops of the posts until after all of the panels have been put. Instead, they leave the tops of the posts “wild.”

A Trick for Attaching Wood Fence Panels to Posts

When you are ready to install a panel, first secure a block measuring four inches in width to the post that is located on higher ground at the appropriate distance from the ground. Next, position the spacer so that it rests on the block, and then extend it to the next post. Place a level on top of the spacer, and then make the necessary adjustments to the height so that the bubble is centred. Create a line that runs over the top of the spacer, and then connect a block so that it is flush with the line and sits below it.

The remaining tasks are simple, even if you are working by yourself. Place the panel on top of the blocks, and then use fasteners measuring three inches to attach it to the posts. When you are finished, take the blocks out of the way.